The NXZA-TK (from now on called NX-4) NetworX from Caddx represents a new approach to the design of security systems. The NX-4 is probably the most. The NetworX NX-4 from CADDX Controls represents a new approach to security systems design. Drawing on our experience in the world market as the largest. Click the photo of your keypad or choose from the list below. CADDX Manuals. CADDX NX E User Manual (PDF, MB) · CADDX NX E User Manual.
|Published (Last):||4 April 2012|
|PDF File Size:||18.43 Mb|
|ePub File Size:||6.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thanks for your help MrRon, I am in australia, would this change the installer code? The corresponding upper zone will become unavailable. If the numerical data to be programmed in a location is “”, press - on the keypad.
When you are in the last segment of a location and press the [r] to enter the data, you will exit jx4 location. To customize a Zone Configuration Group, refer to Locations starting on page. Under this condition, if a force armable zone is not secure, the “Ready” LED will flash. Auxiliary will activate the steady Fire siren, Auxiliary will sound the keypad, and the Keypad Panic can be programmed to be silent or audible sound siren.
Pressing manaul [Exit] nc4 will exit this programming level, and go to the “Select a Module. If you desire the duration of the Dynamic Battery Test to be 0 minutes, you should program --[r] in segment of this location.
Location is used to select which events are reported to Phone. A maximum of keypads and other module excluding hardwire can be added to expand the capabilities of the NX- unit. It’s 0 program the main control 25 go to section The factory default for User is --- when using a -digit code, or -- --- for a -digit code.
GE NetworX NX-4 Manuals
This manual contains proprietary information. Feature selection data will display the current condition on or off of eight features associated with the programming location and segment selected. Enter [minutes ‘s digit] Page. User codes will not be accepted during the enrolling process.
CADDX NetworX NX-4 Control/Communicator Installation Manual
These wireless devices are xn4 UL listed for residential applications. Then get a ladder and push the learning button on the garage opener motor. Once the [Cancel] key is pressed, the “Cancel” LED will illuminate until the central station acknowledges the “Cancel” report. AU Australia More information. The key panel is a nxE.
Entry delay zones can also be made instant. The overseas versions of alarm hardware often differ radically from the N. Power Over-current report enabled. Group Bypass A designated group of zones can be programmed to bypass by pressing [Bypass]- -[Bypass]- [Bypass] prior to arming.
If you say that this is a NX-4, unless there’s something radically different about the export version of this system, then there’s something that I’m missing in your description of your steps.
I am assuming that based on the ” default zone types” is what these numbers represent. The Clean light is flashing You should call for service if the Clean light is flashing and the machine is inoperable.
Helpful 0 Not Helpful Comment Flag. Once the number of the module to be programmed has been entered, the “Armed” LED will illuminate, indicating it is amnual for a programming location to be acddx. Newsletter Sign-Up Signup Email address. When desired, this built-in driver can be easily converted to a amp voltage output through programming. The counter will increment each time an alarm is detected on a zone with multiple trips. Does that make sence?
The system may be programmed to communicate with a central monitoring station to cadddx system events. The alarm report will also be sent. Enable Ding Dong sound for Chime – Manuql off, chime will be a single tone. At the end of the exit delay, these zones will become bypassed.
Caddx NX-4 v1 Program Sheet
If if was wireless, there would be a couple of antennae poking out of the system box, and you would have transmitters on many of the locations instead of just contacts. Off for zones to restore only when siren is off. Consult the instruction manual for your central station receiver to determine which format is compatible, and select from the formats listed on page. How can this be resolved. nz4
Delays of four seconds can be programmed at any point in the phone number by programming a “” in the appropriate segment.